概述  Outline

本裝置系戶內金屬鎧裝抽出式開關設備（以下簡稱開關設備），是 3.6-12 千伏三相交流 50Hz 單母線及單母線分段系統的成套配電裝置主要用于 發電廠，中小型發電機送電、工礦企事業配電以及電業系統的二次變電所的受電、送電及大型高壓電動機起動等。實行控制保護、監測之用，本開關 設備滿足 IEC298、GB3906 等標準要求，具有防止帶負荷推拉斷路器手車、防止誤分合斷路器、防止接地開關處在閉合位置時關合斷路器、防止誤入 帶電室、防止在帶電時誤合接地開關的聯鎖功能，既可配用 VS1 真空斷路器，又可配用VD4真空斷路器。實為一種性能優良的配電裝置。

This equipment is indoor metal armoring with drawable switchgear (hereafter refer to as switchgear. 3.6-12kilovolt three phase AC 50Hz single bus bar and the single bus bar subsection system's omplete electricity distribution equipment is used in the power plant, small and medium-sized generator power transmission, industry and mining business power distribution as well as electrical industry system's second transformer substation's electric take-over , power transmission and large-scale high pressure motor starting and so on. The purpose is to control, protect and monitor. This switch equipment is up to the standard of IEC298、GB3906 and can prevent the charge from pushing and pulling the breaker, from opening and closing the breaker, from insulation with electricity by mistaken, from earthed switch closing the breaker ,from opening the switch's interlock when it with electricity mistakenly. It can not only use with VS1 vacuum circuit-breaker, but with Corporation's VD4 vacuum circuit-breaker. It is indeed a kind of power distribution equipment with superior performance.

使用環境條件  Use environmental conditions

1. 正常條件 

a. 周圍環境空氣溫度：上限，+40℃ 下限，-10℃ 

b. 海拔：1000M 

c. 相對環境濕度：日平均相對濕度不大于 95%，月平均相對濕度平均不大于 90%; 

d. 地震：烈度不超過 8 度。 

e. 周圍空氣應不受腐蝕性或可燃氣體、水蒸汽等明顯污染。 

f. 無嚴重污穢及經常性的劇烈振動，嚴酷條件下嚴酷度設計滿足 1 類要求。

2. 工作條件： 

* 在超過 GB3906 規定的正常的環境條件下使用時，由用戶和制造廠協商。

1. Normal condition

a. Surrounding air temperature:-10℃～ +40℃

b. Altitude : 1000M

c. Relative environment humidity: The daily relative humidity average is not higher than 95%, the monthly relative humidity average is not than higher 90% 

d. Earthquake : The intensity does not exceed 8 degree. 

e. The surrounding air without corrosive or flammable gas or water vapour. 

f. Without a lot of dirtiness and regular fierce vibration, under the severe condition, the intensity meets the first kind requirement. 

2. special working conditions 

* When it is used beyond the normal environmental condition stipulated in the GB3906, the user should consult with the manufacture.

主要技術參數  The main technical parameters

結構簡介   Structure Introduction

開關設備按 GB3906-91 中的鎧裝式金屬封閉開關設備而設計。整流器體是由柜體和中置式可抽出部件（既手車）兩大部分組成，見圖 1。柜體分 四個單獨的隔室，外殼防護等級為 IP4X，各小室間和斷路器室門打開時防護等級為 IP2X。具有架空進出線、電纜進出線及其它功能方案，經排列、組 合后能成為各種方案形式的配電裝置。本開關設備可以從正面進行安裝調試和維護，因此它可以背靠背組成雙重排列和靠墻安裝，提高開關設備的安 全性、靈活性，減少了占地面積。

The switch equipment is designed according to GB3906-91 metal armoring seal switch equipment. The rectifier body is made up of the cabinet body and draw-out parts (namely handcart) placed in the middle. See charter 1. The cabinet divides into four separate rooms, the outer covering protection grade is IP4X,when each small room and the circuit breaker is opened, the protection grade is IP2X.It can suspend the inlet, outlet line, cable's inlet, outlet line and other function plan. After arranged and combined, it can become each kind of plan form of the power distribution equipment. This switch equipment may be installed and maintained from the frontage, therefore it may compose the dual arrangement back to back and be installed against the wall, improving the switch equipment's security and flexibility and making full use of the occupying area.

開關設備結構圖  Switchgear structure diagram

開關柜外形尺寸圖  Switchgear Dimensions

◆ 手車 Handcar

手車骨架采用薄鋼板經 CNC 機床加工后經鉚、焊而成的。根據用途，手車可分為斷路器手車、電壓互感器手車、隔離手車、計量手車等等，相同 規格的手車能方便互換。手車在柜內有隔離位置、試驗位置和工作位置，每一位置均設有定位裝置，以保證手車處于以上位置時不能隨便移動、而移動 手車時必需要解除聯鎖。

The framework of handcart is made of steel sheet through the procession of CNC machine tool and rivet welding. According to the application, the handcarts can be divided into circuit breaker hand-cart, voltage transformer handcart, isolating handcart and metering handcart, etc. The handcarts of the same specification can be exchanged conveniently. In the cabinet, the handcart has isolating position, testing position and operating position, each of which is designed with a location device to assure that the handcart can't move easily at the above-mentioned positions, while the interlock must be unlocked to move the handcart. 

◆ 母線室 Bus chamber 

母線從一個開關柜引至另一開關柜，通過分支母線和靜觸頭盒固定。扁平的分支母線通過螺栓連接于靜觸頭盒和主母線，不需要任何其它的線夾 或絕緣子聯接。當用戶和工程有其它需要時，母線排上的聯接螺栓可用絕緣和端帽封裝。在母線穿越開關柜隔板時，用母線套管固定。如果出現內部故障 電弧，能限制事故蔓延到鄰柜，并能保障母線的機械強度。

The bus is led from one switch cabinet to another one and fixed with static contact box through branch bus. The flat branch bus is connected through the bolt to the static contact box and main bus, not needing any other line clamps or insulators. When there is special demand of the clients or the project, the connecting bolt on the bus bar can be encapsulated with insulation and end cap. When the bus crosses the baffle of the switch cabinet, fix it with bus bushing, so that, if there is any internal fault arc, it can prevent the fault spreading to another cabinet and can guarantee the me-chanical strength of the bus. 

◆ 電纜室 Cable chamber 

電纜室內可安裝電流互感器、接地開關、避雷器以及電纜、并在其底部配制開縫的可卸鋁板，以保障現場的施工方便。

Inside the cable chamber, the current transformer, grounding switch, arrester and cable can be installed, and on the bottom is designed slotted removable aluminum sheet to assure the convenient siteconstruction.

◆ 繼電器儀表室 Relay instrument chamber 

繼電器儀表室用于安裝各類繼電器、儀表、信號指示、操作開關等元器件。此外可根據用戶要求在儀表室頂部增加小母線室，可敷設十六路控制 小母線。

Relay instrument chamber is used to install all kinds of components, such as relays, instruments, signal indicator and operating switch, etc. In addition, it's available to add a small bus chamber on the top of the instrument chamber according to the demand of the clients, and set 16 lines to control the small bus. 

◆ 泄壓裝置 Pressure releasing device 

在手車室、母線室、電纜室的上方設有泄壓裝置，當斷路器或主母線、電纜室內發生內部故障電弧時，伴隨電弧的出現，開關柜內部氣壓上升， 達到一定的壓力后，頂部裝置的壓力釋放金屬板將被自動打開，釋放壓力和排泄氣體，以保障操作人員和開關柜安全。

On the handcart chamber, bus chamber and cable chamber is installed pressure releasing device. When there is internal fault arc in the breaker, main bus or inside the cable chamber, and with the appearance of electric arc, the internal pressure in the switch cabinet rises. After it rises to a certain pressure, the pressure releasing metal sheet of the top device will be opened automatically, and the pressure and the gas are released to guarantee the safety of the operator and the switch cabinet. 

◆ 鎖扣結構 Latching device 

中門與柜體之間的聯接采用鎖扣結構，并配以提升機構，使中門開啟更為方便，當中門處于關閉狀態時，其與柜體的聯接強度更好，增強了有效 抗擊內部燃弧故障的能力。

Latching device is used to connect the central exit and cabinet body, and the lifting device is also designed to make it more convenient to open the central exit. When the central exit stays closed, the connecting strength with the cabinet body is the best and the capability against the internal arcing fault effectively is strengthened.